Step	Item	Action/Details
1	STAB AUG switches	All ON
2	MASTER TEST switch	Set to EMERG GEN
3	MASTER RESET pushbutton	Depress Verify DFCS caution lights extinguished
4	MASTER TEST switch	OFF
5	MASTER RESET pushbutton	Depress Verify DFCS caution lights extinguished. STAB AUG switches should not disengage.
6	Notify RIO	Advise test complete
7	STAB AUG switches	All ON
8	AFTC	L/R ENG MODE SELECT: SEC → PRI
9	Emergency WING SWEEP handle	If not over-swept: Move to 68° Then full OV SW Hold until HZ TAIL AUTH light goes out and OVER flag appears Then stow
10	Wing-sweep mode switch	AUTO
11	WING SWEEP DRIVE NO.1 and WG SW DR NO.2/MANUV FLAP circuit breakers	In
12	WING/EXT TRANS switch	OFF
13	MASTER RESET pushbutton	Depress
14	COMM/NAV/GEAR/DISPLAYS	Set all to ON: - UHF to TR+G or BOTH - TACAN to T/R - ARA-63 to ON - DISPLAYS power switches ON - RADAR ALT ON
15	Trim	Set to 000
16	Standby attitude gyro	Erect
17	MASTER RESET pushbutton	Depress
18	MASTER TEST switch	Set to OBC
19	Autopilot	Engage
20	Speed brake switch	Extend → Retract
21	REFUEL PROBE switch	Extend → Retract
22	WSHLD AIR switch	Cycle
23	OBC	OFF
24	WING/EXT TRANS switch	OFF
25	Trim	Re-check and set to 000

Step	Item	Action/Details
1	EMERG GEN check	Ensure completed before continuing
2	ECS system	Allow ECS to run ≥ 3 minutes before powering avionics/AWG-9
3	CDNU	ON
4	DATA LINK	ON
5	DATA LINK Mode	CAINS/WAYPT (CV Ops) / TAC (Shore Based)
6	NAV MODE Switch	ALIGN
7	WCS switch	STBY
8	PTID power switch	ON
9	LIQ COOLING switch	AWG-9 or AWG-9/AIM-54
10	CDNU	Enter Current Position / Date / Time
11	IR/TV power switch	IR/TV
12	Communications	ON and Set
13	TACAN/EGI select switch	EGI
14	RADAR WARNING RCVR panel	Set
15	DECM knob	STBY Wait for light to go off → HOLD 3 sec → ACT for OBC
16	IFF MASTER knob	STBY
17	AUTO BIT 2	Verify Complete
18	Verify pilot has OBC selected	Check
18a	PTID	Observe ALIGNMENT display
18b	PTID (CM display)	Observe FAILED acronyms
18c	PTID	Observe Test Complete
18d	Altimeter	Reset
19	CDNU	Enter Data / Load Flight Plan
20	Computer Address Panel	Set
21	DDD	Set
22	PTID Controls	Set
22a	Contrast	Set
22b	Bright Control	Set
22c	Data Link	As Required
22d	JAM Strobe	As Required
22e	NON ATTK	As Required
22f	Launch Zone	As Required
23	Multiple Display Indicator	Set
23a	TEST Button	Depress and Check
23b	Brightness	Set
24	DATA/ADF switch	BOTH
25	Hand Control Panel	Set
25a	Light Test (AWG-9 lights)	Depress and Check
25b	EL Vernier	Set 0° EL
26	AN/ALE-47 DCDU MODE/PWR Switch	STBY
27	CANOPY DEFOG-CABIN AIR lever	CABIN AIR
28	D/L Reply	As Required
29	AAI Control Panel	Set
29a	TEST/CHAL CC switch	TEST
30	Indicator Lights	Test
31	DDI BIT	Test
32	After Alignment Completed	Check
32a	NAV Mode	INS
32b	Program Restart	Depress
32c	STBY/READY Lights	OFF
33	DEST Data	Verify
34	BRG/DIST to Destination	Check
35	Own Aircraft Groundspeed	Check
36	MAG VAR	Check
37	KY-58	As Required
38	Standby Attitude Gyro	Erect
39	Notify Pilot	Ready to Taxi